http://spectrum3.esy.es/Juegos/DSK/O/Out%20Run.rar
Desde interna o externa.
Si es externa hay que escribir
Load "b:"
Load "outrun"
![Sonrisa :)](./images/smilies/sc_jsmiley.gif)
Moderador: Fundadores
Gracias! Hacia mucho que me queria poner a diseñar algo parecido pero no encontraba el momento... a pesar de ser para CPC 6128 encajara en un +3 ya que las disqueteras son las mismas.mrbyte escribió: ↑05 Ene 2018, 17:24 hola compañeros,
Aqui teneis el enlace de mi soporte para gotek interno. seria para 6128. la impresion es en 2 piezas, base y frontal que despues se montan encajadas y se fijan. Es una pieza sencilla, q nada tiene q ver con los trabajos del compañero Merlinkv, pero me gustaria ofrecerla como aporte a la comunidad de este foro.
https://mega.nz/#!VbRmVQ5R!R1F9Xa6AtRfn ... fB7yH8ffgo
salu2 y q la disfruteis.
Que bien queda. Enhorabuena por el trabajo!mrbyte escribió: ↑05 Ene 2018, 17:24 hola compañeros,
Aqui teneis el enlace de mi soporte para gotek interno. seria para 6128. la impresion es en 2 piezas, base y frontal que despues se montan encajadas y se fijan. Es una pieza sencilla, q nada tiene q ver con los trabajos del compañero Merlinkv, pero me gustaria ofrecerla como aporte a la comunidad de este foro.
https://mega.nz/#!VbRmVQ5R!R1F9Xa6AtRfn ... fB7yH8ffgo
salu2 y q la disfruteis.
Aqui tampoco funciona. Igual que a ti, rayas magenta y verde.
Speedlock Weak Sector
Used by: After Burner, Barbarian 2, Buggy Boy, Chase HQ 2, Robocop, W.E.C. Le Mans, …
The protection is on cyl 0, and appears as a 9-sector track with the 2nd sector (id=2) showing a data CRC error. The contents of the error sector change between successive reads, with either all or just part of the contents appearing different. Some of the remaining sectors may also have a deleted data address mark.
250Kbps MFM, 9 sectors, 512 bytes/sector:
0.0 1 2[m3,dc] 3d 4d 5d 6d 7d 8d 9
diff(72): =256 -32 +48 -176
This example represents a partially weak sector; the first 256 bytes of the sector are the same each time, the next ~32 bytes differ between reads, a further ~48 bytes are filler bytes (but have changing value), and the final ~176 bytes differ between reads. In some early versions of Speedlock the weak and filler blocks were 16 and 64 bytes in length, respectively.
The protection checks vary between titles, but in all cases it reads up to 3 copies of the sector and expects to encounter a data CRC error and a difference between the copies read. In some versions of the protection it checks for unchanging filler at the start of the data field. Some also check for a patch of filler bytes beyond the weak area.
To write the weak sector SAMdisk prepares the track area using an 07 filler written at 300Kbps, which was found to be particularly effective at losing FDC sync when the data is read back at a normal 250Kbps. A normal sector header and data address mark is then written to overlap the 'weak' area, followed by the required number of constant bytes in the data area. For partially weak sectors a constant block of 256+80=336 bytes followed by a weak area of 176 bytes is sufficient to satisfy all known variations of the protection check.
For this protection to work in emulators they must support the EDSK extension to use multiple copies of error sectors, ideally cycling through the different data copies each time the sector is read. Fuse, SpecEmu and Spin support this, though other emulators may vary the final byte in the sector in order to pass the weak data check.
las disqueteras son las mismas, pero en el cpc se fija mediante una L metalica que es lo que utilizo para adaptar este soporte, no se como es en el spectrum +3, pero agradeceria si alguno prueba el modelo que comentara y pasara alguna foto.BCH escribió: ↑06 Ene 2018, 03:50Gracias! Hacia mucho que me queria poner a diseñar algo parecido pero no encontraba el momento... a pesar de ser para CPC 6128 encajara en un +3 ya que las disqueteras son las mismas.mrbyte escribió: ↑05 Ene 2018, 17:24 hola compañeros,
Aqui teneis el enlace de mi soporte para gotek interno. seria para 6128. la impresion es en 2 piezas, base y frontal que despues se montan encajadas y se fijan. Es una pieza sencilla, q nada tiene q ver con los trabajos del compañero Merlinkv, pero me gustaria ofrecerla como aporte a la comunidad de este foro.
https://mega.nz/#!VbRmVQ5R!R1F9Xa6AtRfn ... fB7yH8ffgo
salu2 y q la disfruteis.
Cual modelo de OLED es el que encaja?
El +3 tambien lleva una L metalica, aunque no se si tiene las mismas medidas. Hoy lo mirare
Hola con sdd 1306 me salen varias. ¿Puede ser la de 0.91" 128x32 ?
delgrom escribió: ↑07 Ene 2018, 22:05Hola con sdd 1306 me salen varias. ¿Puede ser la de 0.91" 128x32 ?
Por ejemplo esta:
https://www.ebay.es/itm/IIC-I2C-0-91-12 ... SwjDZYl6oC