Re: Chip Tester de 8bit-museum.de - Reloaded
Publicado: 20 Sep 2020, 21:09
Retroinformática y consolas entre amigos sin complejos
https://www.va-de-retro.com/foros/
Esto está puesto en las instrucciones en inglés de Slabbi te dice cómo configurar el Arduino y hacer el cable y todo.nandove escribió:geloalex escribió: ↑20 Sep 2020, 19:55 Hi Slabbi what is the better option for programing the Atmel via ISP??
Can I use an arduino Uno or Leonardo??
Or this option that comments nandove?
Another question about jumpers:
JP2 an JP3 must be selected when no barrel power (JP1 and JP4 opened)
If barrel selected we have JP2 and JP3 open ....right?
Thanks Slabbi
Un amigo que sabe un huevo, me ha indicado que si tienes un arduino, hay un sketch que transforma un arduino normal en un programador AVR:
https://www.arduino.cc/es/Tutorial/ArduinoISP
En mi caso, no tengo un arduino :/
Gracias pero preferí verificarlo porque hay discrepancias, por ejemplo y si no recuerdo mal, en el manual para la resistencia R1 de la Opción # 2 del módulo de alimentación aparece el valor 1K y en la placa 2k2.slabbi escribió: ↑19 Sep 2020, 17:47La lista de materiales es correcta.
Encontraste la lista de materiales en Dropbox usando el enlace que recibiste de mí o en el manual.
Además, todos los valores están impresos en la PCB y los valores son correctos.
No se preocupe. Utilizo fotos antiguas en y en el manual, eso es todo.
Yes. You can use 2.2k or 1k. I use usually low power LED, so 2.2k is fine. Most people use "normal" LEDs, so the LED is a little bit dark and 1k is more suitable.
It's good! If you order from "Mouser" you should definitely check all components before welding. I looked for an error together with a user and it turned out that one of the supplied PNP transistors were of a completely wrong type. Difficult to find later. The best thing to do is to briefly review all the values so there are no wrong ones.
Tienes razón.... las imprimí en el chollo y las deje allí cuando marche de vacaciones , contaba con empezar a montar cuando volviera.rgrocha escribió: ↑20 Sep 2020, 22:16Esto está puesto en las instrucciones en inglés de Slabbi te dice cómo configurar el Arduino y hacer el cable y todo.nandove escribió:geloalex escribió: ↑20 Sep 2020, 19:55 Hi Slabbi what is the better option for programing the Atmel via ISP??
Can I use an arduino Uno or Leonardo??
Or this option that comments nandove?
Another question about jumpers:
JP2 an JP3 must be selected when no barrel power (JP1 and JP4 opened)
If barrel selected we have JP2 and JP3 open ....right?
Thanks Slabbi
Un amigo que sabe un huevo, me ha indicado que si tienes un arduino, hay un sketch que transforma un arduino normal en un programador AVR:
https://www.arduino.cc/es/Tutorial/ArduinoISP
En mi caso, no tengo un arduino :/
Sent from my Pixel 3a using Tapatalk
Hi Stephan,slabbi escribió: ↑20 Sep 2020, 21:36 Please report your experience with that programmer.
I usually recommend this one
https://www.diamex.de/dxshop/USB-ISP-Pr ... ex-Prog-S2
because it also flashes STM32 and LPC-Cortex (Prog-S2)
or this
https://www.diamex.de/dxshop/USB-ISP-Pr ... -Atmel-AVR
1 2 3 4 - off - - programmer provides no voltage off on - - programmer provides 3.3V on on - - programmer provides 5V 1 2 3 4 - - off off Atmel AVR using ISP - - off on STM32 Cortex-M using UART - - on off NXP/LPC Cortex-M using UART - - on on USB/Serial converter without controlling the handshakeSo on/on/off/off (^/^/v/v) is for 5V Atmel.